|
POSTS: All
posts shall be 14 gauge with 3/8" x 7/8" slots punched on 1-1/2" vertical
centers for shelf adjustment using non-intrusive
compression clips. Sway braces shall be attached
to the post with nuts and
bolts that shall not interfere with shelf adjustment.
BEADED POST: Shall
be 14 gauge 11/16" wide
x 2-9/16" deep overall. Units to have front beaded posts.
Beaded posts used on open units shall have legs spot-welded together
on 6" centers for added strength. Legs shall be punched
on 3" centers for the attachment of side sway braces.
ANGLE POSTS: Shall
be 14 gauge side leg 2-5/16" wide, rear leg is 1-3/16". Post to be offset
angle shape. Starter units shall have rear angle posts. Flanges
shall be punched on 3" centers for the attachment of side
and back sway braces.
TEE POSTS: Shall
be two angle posts spot-welded together on
6" centers.
Adder units shall have rear T posts.
END PANELS: Closed
starter units shall have end panels. Each
end panel shall consist of one beaded post,
one angle post and one 24 gauge side sheet
spot-welded on 6 " centers.
INTERMEDIATE PANELS: Shall be the same
as end panels except they shall have 2 angle posts and shall
be furnished on closed adder units.
BACKS: Shall
be 24 gauge with holes on 1" centers for bolting to angle
or tee posts.
SWAY BRACES: Shall
be 12 gauge x 3/4" wide
ends punched for bolting to posts. Also punched
in the middle for bolting to each other for
strength and ease of installation.
SHELF CLIP: One
piece 13 gauge compression type independently
adjustable. Each clip shall bear on the edges
of two post notches and provide a minimum of
1-1/2" of bearing.
Zinc plated. Provide four independently adjustable
clips per shelf.
SHELVES: Shelf
shall have a 1-1/4" face
on all four sides. Front and rear flanges shall have a 3/4" wide
box formation with return flanges spot-welded to the shelf bottom
on 3" centers. Sides shall have a 5/8" 90 return flange.
Corner shall be lapped and spot-welded. Medium and heavy duty
shelves shall have ribs in the tabs to keep shelf clips snug.
Shelves shall be punched for dividers on 1-1/2" centers.
Shelves shall be furnished in medium duty,
heavy duty or extra heavy duty to meet the specified capacity.
SHELF REINFORCING: Shall consist of
13 gauge side shelf supports tabbed to fit into clip slots and
14 gauge center shelf supports. Center support shall be held
in place by engaging the side shelf supports. Shelf reinforcing
shall be furnished when specified shelf capacity exceeds the
rated capacity of the extra heavy duty shelf.
SHELF DIVIDERS: Shall
be 24 gauge through 20" high; over 20" high dividers shall be 20 gauge.
Fronts of dividers shall have a 5/16" diameter bead. Top,
bottom and rear flanges shall be 7/8". Dividers shall be
held in place with plastic buttons.
ANGLE DIVIDERS: Shall be 18 gauge and
held in place with plastic buttons.
SLIDING DIVIDERS: Shall
be 20 gauge. Divider portion shall be sloped
at 45 at the front with a 1/2" radius
at the front corner.
COUNTER TOPS: Shall
be 14 gauge with a 2" high face and 13 gauge counter end
finishing caps attached with concealed nut and
bolts.
BASE FRONT: Shall be 18 gauge and attached
to the shelf by bolting.
BIN FRONTS: Shall
be 18 gauge and attached to the shelf by
bolting. Bin fronts shall be 1", 2" or
3" high.
FOOTPLATES: Shall
be 2-1/4"x 3-1/2" x
12 gauge with a bracket welded on top. Footplates protect floor
covering, spread the load and can anchor shelving to the floor.
Plate has a 7/16" diameter hole for anchoring and an embossment
for shim alignment.
SHIMS: Shall
be 16 gauge 2-1/4" x
3-1/2" holes and embossment same as for foot plate.
CORNER ANGLE BRACE: Shall
be 13 gauge notched to form an "L" shape and shall be 13/16" wide
with holes for attaching to the post and shelf.
Braces are used for pass through units.
SWINGING DOORS: Door and frame assembly
complete with 3 point locking, chrome plated turn handle with
built in lock with two keys. Doors are 20 gauge with reinforcing
pans. Frames 16 gauge. Each pair of doors cover one shelving
unit.
SLIDING DOORS: Shall
be 22 gauge doors with 18 gauge reinforcing
pans welded inside door. Includes a
cylinder lock, 2 keys, nylon rollers and glides,
and recessed handles. Side frame members
shall be 20 gauge. Top and bottom
frame member each shall be two piece 18 gauge
assemblies. Sliding doors shall be 72" wide and cover two 36" wide
shelving units.
SHELF BOXES: Shall
be 20 gauge 4-5/8" high
with an integral rigid curled handle on the box front. Box front
and rear panel shall be punched for card holders, sides punched
for 1" divider adjustment.
SHELF BOX DIVIDER: Shall be 20 gauge
punched for card holders.
POST SPLICE CHANNEL: Shall be 16 gauge
and formed into a channel shape. Center of channel shall be punched
with four holes for assembling to upper and lower post. Used
when added height is required.
ERECTOMATIC AND HI-PERFORMANCE ARE REGISTERED
TRADEMARKS OF PENCO PRODUCTS, INC.
PENCO RESERVES THE RIGHT TO VARY SPECIFICATIONS
CONSISTENT WITH ITS POLICY OF CONTINUOUS PRODUCT IMPROVEMENT.
| 
